Axis CAMERA RECORDER 1.1 Manual do Utilizador

AXIS Camera RecorderUser’s Manual

Devices - Quick Setup 10Devices - Quick SetupThis short description will help you set up your first device, without going into too much detail. It i

Devices - Quick Setup 11 Now that a device has been added we will add the camera to the Monitor application and configure its layout.1. Click the Moni

Devices - Quick Setup 12Using the Monitor application1. Now open the Monitor application. You should now see the image from your camera. If not, the

The Administrator Application 13 The Administrator ApplicationThe Administrator application is used when setting up the system for the first time, whe

The Administrator Application 14• Add Device - Add new cameras or video servers. See the previous section Devices - Quick Setup, on page 10 and the

The Administrator Application 15 MAC address (S/N) - This is the hardware address of the camera/video server, e.g. 00408c291ba2 and it corresponds to

The Administrator Application 16Configuring Video ServersFor video Servers, you must specify if the connected cameras are Pan/Tilt/Zoom cameras or n

The Administrator Application 17 Configuring Monitors and the LayoutOnce the software has been configured for your cameras and video servers, you shou

The Administrator Application 18Hot Spot Window - This special window can be used for various purposes and will, when enabled, occupy up to 9 (3x3)

The Administrator Application 19 Save images within … - If Images with motion has been selected as the recording condition, it is then also possible

AXIS Camera Recorder User’s Manual 2 About This DocumentThis manual is intended for administrators and operators of AXIS Camera Recorder and is appl

The Administrator Application 20For all cameras combined, a maximum total of 160 GByte can be saved.Delete images older than - (in minutes, hours o

The Administrator Application 21 Exclude Regions SettingsIt is also possible to set up regions for the camera that should be excluded from motion dete

The Administrator Application 22Calibrating Motion DetectionThe motion detection system can control (a) when images are saved to disk, and (b) when

The Administrator Application 23 Noise Sensitivity Slider - Adjusts the noise sensitivity level of individual picture elements (pixels). The noise sen

The Administrator Application 24Defining Motion Detection Exclude AreasAreas that should not be included in the motion detection area can be exclude

The Administrator Application 25 Setting Up and Using PTZ Preset PositionsUp to 25 PTZ preset positions (PP’s) can be created for absolute positioning

The Administrator Application 26Tilt (Vertical bar) - Click on the bar to set the tilt position for the camera. When clicking, the tilt level will b

The Administrator Application 27 General SettingsThe General Settings dialog box allows you to define various administrative settings, as described be

The Administrator Application 28E-mail SetupThe e-mail alerting system must be configured prior to use. The following settings must be configured; E

The Administrator Application 29 Scheduling Camera Activity and Alert PeriodsUsing a a one-week calendar, the built-in Scheduler provides automatic co

AXIS Camera Recorder User’s Manual 3 Table Of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The Administrator Application 30E-mail - Check to enable (or delete) periods during which e-mail alerts will be sent for events for the selected cam

The Administrator Application 31 6. Click the day name again to zoom out.7. You should now see a purple bar that represents the times you specified. T

The Monitor Application 32The Monitor ApplicationThe Monitor application is the heart of the AXIS Camera Recorder system, and is used for all normal

The Monitor Application 33 When the Monitor application is started, it automatically starts any cameras that have been specified in the Scheduler as b

The Monitor Application 34Buttons for manual control of outputs - These buttons are used to manually control any outputs that have been linked to t

The Monitor Application 35 The Hot Spot window supports interactive Pan/Tilt/Zoom. When PTZ Mode is enabled, click in the Hot Spot window and hold dow

The Monitor Application 36Camera - Select the camera to view recordings from.Data/Time - Use these controls and press the Go To button to jump direc

The Monitor Application 37 Features in Advanced ModeAdvanced mode allows you to print or export individual images, create AVI video files and zoom int

The Monitor Application 38• Create AVI - Press this button to create an AVI file, using the images included in the period/region defined by start ti

Inputs and Outputs 39 Appendix A - Inputs and OutputsAdvanced Control with Input DevicesAxis Network Cameras and Video Servers support the use of vari

Introduction 4IntroductionAXIS Camera Recorder is a powerful and flexible surveillance solution that turns your TCP/IP-based Axis network cameras an

Inputs and Outputs 40A plus sign (+) will now appear to the left of the device to which the sensor is connected. Click this to see the defined exter

Inputs and Outputs 41 6. Now find the start time of the event-controlled period and click and drag the mouse to the end time. 7. You will now be asked

Inputs and Outputs 42I/O ControlClicking on the I/O Control button brings up a group of panels from where it is possible to define which events will

Installation Guide 5 Installation GuideThis installation guide will help you install AXIS Camera Recorder and configure it for your Axis Network Camer

Installation Guide 6System RequirementsBefore installing, you should be aware of the various requirements that will apply for your application, and

Installation Guide 7 Hard Disk SpaceThe amount of disk space required can be roughly calculated from the table below. Always add a further 5-10% disk

Installation Guide 8Installation Step 1 - Locate your License CodeTo install the full retail version of AXIS Camera Recorder a valid license code mu

Installation Guide 9 If a demo version of AXIS Camera Recorder was already installed, it will be necessary to remove the image databases. This can be