Axis 1620 Manual do Utilizador Página 279
- Página / 441
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
11-5
IM 701610-01E
Saving and Loading Data to and from the Storage Medium
11
11.4 Connecting USB Storage to the USB PERIPHERAL
Interface
Specifications of the USB PERIPHERAL Interface
Item Description
Connector type USB type A connector (receptacle)
Electrical and mechanical USB Rev. 1.1
Data rate 12 Mbps max.
Power supply 5 V, 500 mA* (per port)
Number of ports 2
* Devices with maximum consumption currents exceeding 100 mA cannot be connected to two
ports at the same time.
Port 1
Port 2
1 2 3 4
Pin No. Signal Name
1 VBUS: +5 V
2D--Data
3D++Data
4 GND: Ground
Connecting USB Storage
When connecting USB storage, directly connect the storage device to the instrument
using a USB hub as shown below. You can connect the USB cable regardless of
whether the power to the instrument is ON or OFF (supports hot-plugging). When the
power switch is ON, the USB storage device is detected and enabled approximately six
seconds after it is connected.
USB PERIPHERAL
DL1620/
DL1640/
DL1640L
USB storage
Compatible USB Storage
The instrument is compatible with USB mass storage class devices including hard disk
drives, MO drives, and flash memory devices.
Note
• Do not connect USB devices other than a USB keyboard, USB mouse, USB printer, or USB
storage device to the USB PERIPHERAL connector.
• The instrument has two USB PERIPHERAL connectors, but two USB devices with maximum
consumption currents exceeding 100 mA cannot be connected at the same time.
• The instrument does not detect some of the flash memories. If the instrument does not detect
the flash memory, it cannot be used. For details on compatible flash memories, contact your
nearest YOKOGAWA dealer.
- DL1620/DL1640/DL1640L 1
- Product Registration 2
- Foreword 3
- Trademarks 4
- Revisions 4
- Standard Accessories 6
- Optional Accessories 7
- Optional Spare Parts 7
- Safety Precautions 8
- IM 701610-01E 10
- Structure of the Manual 11
- DL1640/DL1640L Version 13
- Contents 14
- Chapter 6 Triggering 15
- Chapter 8 Display 15
- Chapter 9 Waveform Analysis 15
- Chapter 14 Other Operations 17
- Chapter 16 Specifications 17
- Appendix 17
- 1.1 Block Diagram 18
- 500 Lines 20
- Position: 2 div 22
- Position: –2 div 22
- Position: 0 div 22
- Vertical 23
- Input terminal 23
- 1.3 Setting a Trigger 25
- Trigger is activated 26
- When CH1 = and CH2 = 27
- Half the Amplitude 28
- Trigger Level Amplitude 28
- Hysteresis Width 29
- Display Record Length 30
- Trigger Position 30
- Envelope 32
- Selected Record No. 0 34
- Selected Record No. –25 34
- Waveform Label 35
- Trigger Mark 35
- Scale Values 35
- Selects use of 35
- 2 waveform windows 35
- Main Waveform 37
- Z1 Waveform 37
- Z2 Waveform 37
- 1.5 Analyzing the Waveform 38
- Measurement 39
- ( ) 42
- Selected Record No. 0 43
- Selected Record No. –25 43
- Selected Record No. 28 43
- Conditions: 44
- Clock Channel : CH1 44
- Personal 47
- Computer 47
- 1.7 Other Useful Functions 49
- Snapshot <Section 4.6> 50
- Preset <Section 5.6> 50
- Floppy Disk Drive 51
- Zip Drive, or 51
- PC Card Interface 51
- 2.1 Front Panel/Rear Panel 52
- USB PREPHERAL 53
- VERTICAL Group 54
- HORIZONTAL Group 54
- TRIGGER Group 54
- Other Menus 55
- 2.3 Screens 57
- 3.1 Precautions During Use 59
- 3.2 Installation 61
- Installation Position 62
- Rubber Feet 62
- 3.3 Connecting the Power Cord 63
- Response at Power ON 65
- For Accurate Measurement 66
- Response at Power OFF 66
- 3.4 Connecting a Probe 67
- PROBE POWER (OP) 68
- PROBE POWER(OP) 68
- Current Consumption [mA] 69
- 3.6 Setting the Date and Time 72
- Entering a Value 74
- Entering a Character String 75
- Connecting a USB Keyboard 76
- Operations Using a USB Mouse 79
- Scroll bar 82
- 4.2 Initializing Settings 84
- 4.3 Performing Auto Setup 86
- Settings Made by Auto Setup 87
- 0 V (If Adjust Mode is 0 V) 87
- 4.7 Calibration 92
- 4.8 Using the Help Function 94
- 5.1 Turning Channels ON/OFF 95
- Relevant Keys 100
- Operating Procedure 100
- Explanation 100
- GO/NO-GO 101
- 5.6 The Preset Function 103
- 5.11 Selecting the Timebase 111
- [Input Terminal] 112
- Front Panel 112
- DL1640/DL1640L 112
- Rear Panel 112
- 5.12 Setting T/div 113
- 5.12 Setting T/div 114
- T/div and Roll Mode 114
- 6.1 Setting the Trigger Mode 115
- 6.2 Setting the Trigger Delay 117
- 6.4 Setting the Hold Off Time 120
- (SIMPLE) 127
- The Level setting for each 129
- Line No 151
- 7.1 Setting the Record Length 155
- 7.2 Acquisition Mode 156
- 7.6 Using the History Memory 162
- (History Search Function) 165
- 8.3 Changing the Graticule 177
- 8.8 X-Y Waveform Display 184
- 8.9 Zooming the Waveform 186
- Parameters 219
- Set the measurement range 224
- (T-Range) to match the burst 224
- Burst1, Burst2: Burst Width 224
- “*****.” 225
- 9.3 Statistical Processing 226
- Waveforms 240
- 9.7 Smoothing 247
- 9.8 Phase-Shifted Display 249
- Output Signal 259
- Output Connector 259
- Output Timing 259
- (Option) 261
- Printer (Option) 263
- Storage Medium 270
- File Name (Color Information) 272
- Eject Button 275
- Access Indicator 275
- 11.2 Zip Disks 276
- 11.3 PC Card 278
- Interface 279
- Loading the Waveform Data 288
- Unloading Waveforms 288
- Loading Snapshot Waveforms 298
- Clearing the Waveform 299
- Web server functions 303
- 11.12 Copying Files 311
- <40Vpk 1MΩ 319
- 1MΩ/28PF 319
- External Clock Input Terminal 320
- TRIG OUT Terminal 321
- Output Circuit Diagram 321
- Timing Chart 321
- *1: HIGH (High Level) Period 322
- *2: LOW (Low Level) Period 322
- RGB VIDEO OUT Terminal 323
- Specifications 323
- Connecting the Monitor 324
- 12.4 Using the CH1 OUT Signal 325
- Connection Method 327
- Ethernet Interface (Option) 332
- Function) 333
- Strings.” 334
- (FTP Client Function) 336
- Printer (LPR Client Function) 339
- Procedure 351
- Operating Environment 354
- Preparations on the Computer 357
- Data size: Approx. 1.5 MB 359
- Item Security Level 360
- Using the Web Server Function 361
- Update indicator 362
- Indicator 369
- Using Control Scripts 371
- Displaying the Log 373
- Viewing the Link Destination 376
- Drive (Version 1.13 or Later) 377
- Click Sound 382
- Brightness of the Backlight 384
- Connected(Option) 387
- 15.1 Troubleshooting 389
- Error Messages 390
- Status Messages 390
- Error in Setting (880 to 959) 393
- Circuit Breaker Position 400
- Circuit Breaker Activation 400
- Resetting the Circuit Breaker 400
- 16.1 Input Section 402
- 16.2 Trigger Section 403
- 16.3 Time Axis 405
- 16.4 Display 405
- 16.5 Functions 405
- Analysis 406
- Screen Data Output 407
- Data Storage 407
- Other Functions 407
- 16.7 Storage 408
- 16.10 Computer Interface 410
- 16.11 General 411
- 16.12 External Dimensions 413
- Integ2XY 427
- -7.7000000E+01 2.0000000E+04 429
- 0.0000000E+00 -2.5000000E-06 429
- PhaseShift 430
- *6: Data Type 431
- Appendix 4 List of Defaults 432
- Keyboard 433
- Symbols Page 437
Manuais e produtos relacionados com Digitalizar e Imprimir Axis 1620
Digitalizar e Imprimir Axis 542+ Manual do Utilizador
(190 páginas)
(190 páginas)
Digitalizar e Imprimir Axis AXIS USB Guia do Utilizador
(122 páginas)
(122 páginas)
Digitalizar e Imprimir Axis 5800 Manual de Serviço
(90 páginas)
(90 páginas)
Digitalizar e Imprimir Axis 660 Guia do Utilizador
(88 páginas)
(88 páginas)
Digitalizar e Imprimir Axis 5800 Manual do Utilizador
(171 páginas)
(171 páginas)
Digitalizar e Imprimir Axis 5550 Manual do Utilizador
(161 páginas)
(161 páginas)
(34 páginas)
Digitalizar e Imprimir Axis 570 Guia de Instalação
(10 páginas)
(10 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais